Plumbing Basics: What You Need for Installing a Bathtub

Check Us Out

How do you really feel in relation to A Step-by-Step Guide to Installing a Bathtub?


How to Install a Bathtub
Mounting a bath tub isn't precisely brain surgery, however it does require solid plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably challenging job. If the old bathtub is conveniently accessible, the task can move immediately; if you need to open a wall surface to get rid of the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will need an assistant to move out the old tub and set in the brand-new one. Ensure you have actually qualified yourself for the work and are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed job, it is better to consider utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This article will assist you set up a new tub in your washroom if you have actually currently gotten a new tub and do not require to transform the plan of your previous water pipes.
Your devices as well as material list should consist of the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you need to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be quite problematic because of the restricted access that is commonly the instance.
    Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
    Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipelines.
    If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in location between the tap as well as the sink. Secure the faucet in place with the manufacturer provided backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous kind must be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Setting up the Bathtub


    Making use of the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny points.
    The following objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bathtub until the spirit level checks out degree.
    To mount faucets, fit all-time low of the furthest adaptable faucet adapter to the proper supply pipeline by making a compression join; after that do the exact same for the various other tap.
    Activate the water supply and also examine all joints as well as new pipework for leaks and also tighten them if needed. Load the bath tub and likewise check the overflow outlet and the regular electrical outlet for leaks.
    Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub must wait up until the bath tub has been utilized at least when as this will resolve it into its final placement.

    Getting ready for the Installation


    To start with, the sustaining frame supplied with the bathroom must be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets device to prevent strain on the bathtub.
    Fit the versatile faucet ports to the bottom of both faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last placement.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a rigid seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing difficulties with moisture as well as possible leaks to the ceiling below.
    You can choose from a selection of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to permit the motion experienced when the bathtub is in usage. The sealer can split relatively early if you do not think about this movement prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    We were shown that article about Tools You Need to Install a New Bathtub through a good friend on another website. Kindly take the opportunity to share this blog if you liked it. Thanks a bunch for your time. Don't forget to pay a visit to our blog back soon.


    Browse Website

    Leave a Reply

    Your email address will not be published. Required fields are marked *